动车组司机室空调蒸发器气动噪声数值仿真

为研究动车组司机室空调蒸发器的噪声响应，建立某型司机室分体式空调蒸发器的计算流体动力学模型，采用FLUENT中的大涡模拟（large eddy simulation, LES）计算瞬态气动流场。对瞬态流场数据进行傅里叶变换，得到空气流场的频域数据。基于流场频域数据，采用Virtual.Lab的边界元法计算蒸发器的气动噪声，采用声压法计算蒸发器的辐射声功率，并与测试结果进行对比分析。结果表明：蒸发器出口位置气动噪声最高，最大声压级高于56 dB；最大声功率级出现在125~400 Hz的低频段；声功率级随着频率的增加逐渐降低，但在5 000 Hz的高频辐射中声功率级仍然超过55 dB，这表明空调蒸发器气动噪声属于宽频噪声；计算结果与测试结果吻合良好，验证声压法计算空调蒸发器气动声功率可行。     

外部气体辅助注塑制品翘曲变形数值模拟

基于聚合物黏弹性理论与外部气体辅助注塑（EGAIM）的特点，构建了EGAIM气体保压阶段及脱模后自然冷却阶段制品内应力?应变的力学模型。在此基础上，采用耦合有限元法（FEM）对EGAIM平板制件的翘曲变形进行模拟计算，模拟结果与实验结果基本一致，验证了所建计算模型有效可靠。     

Influence of pores arrangement on stability of photonic structures during sintering

Discrete Element Method (DEM) has been used for numerical investigation of sintering-induced structural deformations occurring in inverse opal photonic structures. The influence of the initial arrangement of template particles on the stability of highly porous inverse opal α-Al₂O₃ structures has been analyzed. The material transport, densification, as well as formation of defects and cracks have been compared for various case studies. Three different stages of defects formation have been distinguished starting with local defects ending with intrapore cracks. The results show that the packing of the template particles defined during the template self-assembly process play a crucial role in the later structural deformation upon thermal exposure. The simulation results are in very good agreement with experimental data obtained from SEM images and previous studies by ptychographic X-ray tomography.     

开关磁阻电机结构性转矩脉动抑制方法

开关磁阻电机具有结构简单、成本低和调速范围广等优势,但其双凸极结构和控制器的开关特性,导致存在转矩脉动现象,使得抑制转矩脉动成为焦点问题。首先从开关磁阻电机的结构和运行机理出发,针对线性解析方法难以分析转矩特征的问题,建立电机有限元模型求解出转矩特征并进行样机验证试验。分析样机结构参数对转矩脉动的影响,针对结构参数耦合问题,选择NSGA-Ⅱ算法在参数优化平台上对样机结构参数进行多目标寻优,在保证优化后样机的转矩脉动系数和平均转矩均优于初始电机的条件下,最终获得样机最优化结果。结果表明,不同结构参数对电机转矩的影响有较大的差异,对结构参数的优化能有效地抑制转矩脉动,该参数优化方法可以为开关磁阻电机结构性转矩脉动抑制提供参考。     

管壳式换热器的数值模拟和管束支撑分析

以某固定管板换热器为例，对数值模拟方法和管束支撑进行了研究。通过建立不同单元类型的换热器有限元模型，以换热器壳体轴向应力为指标，对比换热器筒体和管子中的轴向应力及管板挠度，研究了不同换热器有限元分析方法的合理性，考察了管板横向变形和换热管外侧及筒体内侧施加的壳程压力对筒体轴向应力的影响，以及换热管对换热器管板的支撑作用。     

Finite element optimization of sample geometry for measuring the torsional shear strength of glass/metal joints

Assessment of mechanical properties of glass/metal joints is a challenging process, especially when the application relevant conditions of the joints have to be considered in the test design. In this study, a finite element method (FEM) is implemented to analyze a torsional shear strength test designed for glass-ceramic/steel joints aiming towards solid oxide fuel/electrolysis cells application. Deviations from axial symmetry of the square flanges (ends) of respective hourglass-shaped specimens and also supporting and loading sockets of the test set-up are included in the model to simulate conditions close to reality. Undesirable tensile stress and also shear stress concentration appear at the outer edge of glass-ceramic layers, which are less for the hollow-full specimen. The simulation results show that for a specimen with either 9 mm thick square- or 6 mm thick triangular-flanges, locally enhanced tensile stresses almost disappear, resulting in a symmetric shear stress distribution. The difference between the analytically derived nominal shear strength and the real critical shear stress derived via simulation reduces with decreasing the fracture torque.     

面向流屑角突变建模的切削状态参数经验公式的获得及应用

从提高流屑角突变模型的预测精度出发,建立了切削状态参数与3个切削控制参数之间关系的新经验公式。提出了一种通过迭代法准确设定有限元仿真软件刀-屑摩擦因数的方法,并通过直角切削Al6061-T6工件的有限元仿真试验,获得了一组不同切削控制参数组合条件下的切削状态参数数据。根据该数据拟合出剪切角φ、刀-屑摩擦角β、剪切应力τs关于刀具前角γ0、进给量f和切削速度v的经验公式,并通过一组直角切削试验,验证了所得经验公式的有效性。将新建经验公式应用于流屑角突变建模过程后,所得模型关于突变临界切削宽度的平均预测误差减小了27.2%。     

铸造式和焊接式主轴箱体的动态特性对比分析

利用有限元法和试验模态法对立式加工中心的铸造式和焊接式两种结构的主轴箱体进行了模态分析,分别获得了其前六阶固有频率和振型。通过对比两种方法获得的结果,验证了有限元分析模型的有效性。研究表明,两种主轴箱体的阻尼比接近,但焊接式主轴箱体的各阶固有频率均要高于铸造式主轴箱体的各阶固有频率。并且铸造式主轴箱体的固有频率更接近于机床主轴的常用工作频率,焊接式主轴箱体的则远离此频率。因此对于常用主轴转速而言,焊接式主轴箱体的动态性能要优于铸造式主轴箱体的动态性能。     

折臂式随车起重机转台的拓扑优化设计

为了使折臂式随车起重机转台在最大应力不超过材料许用应力的前提下实现轻量化设计的目的,通过ADAMS软件仿真确定其极限工况,对转台进行静力学分析及拓扑优化。通过拓扑优化得到了理想的材料分布。基于优化结果调整转台结构,并对改进后的转台进行静力学分析。结果表明,优化后的转台能够满足实际的使用需求。同时,转台质量降低了12%,证明了优化设计的有效性和可行性,并为折臂式随车起重机的相关设计提供了一定的借鉴。     

Time reversibility of the discrete element method

An algorithm is presented for discrete element method simulations of energy-conserving systems of frictionless, spherical particles in a reversed-time frame. This algorithm is verified, within the limits of round-off error, through implementation in the LAMMPS code. Mechanisms for energy dissipation such as interparticle friction, damping, rotational resistance, particle crushing, or bond breakage cannot be incorporated into this algorithm without causing time irreversibility. This theoretical development is applied to critical-state soil mechanics as an exemplar. It is shown that the convergence of soil samples, which differ only in terms of their initial void ratio, to the same critical state requires the presence of shear forces and frictional dissipation within the soil system.